Russia, Moscow region, Moscow +79041000555

How to install a faucet in the kitchen: installation methods, connection to communications

Takes ~2 minutes to read

The faucet is considered one of the main sanitary appliances in the kitchen, but over time it breaks down and needs urgent replacement. From our article we will learn how to install a faucet in the kitchen.

Save

Dismantling the old mixer and preparatory work

Before dismantling the device, it is necessary to close the valves on the central water supply. Taps are usually installed at the entrance to the apartment or under the sink. After closing the valves, drain the water, place a basin under the hoses and unscrew the nuts. Now you need to unscrew the old device. If access to it is difficult, remove the sink; in this case, you need to pull out the corrugation from the sewer and twist it into a ring near the siphon.

Now that the sink is removed, the plumber has easy access to the studs and the corkscrew nut. If it is impossible to unscrew it with a regular key, they take radical measures - cut it off with a grinder. This is especially true when connecting the mixer to old metal pipes. Next, we inspect the joints of the supply hoses to the water supply. If necessary, a factory extension cord is packed in this place, which will be the key to normal connection with the hose.

If desired, additional taps are installed on the supply pipelines to shut off the water, bypassing the central riser. When installing a plastic liner, adapters are packed.

If the device is installed on an old sink, the user must clean the adjacent area from rust and accumulated dirt. Before installing the faucet in the kitchen on the countertop, you need to take an electric drill with a crown and drill a hole in it.

Save

Installing a new faucet

All types of taps differ in design; they can be mounted on a sink or countertop. In most models, fastening is carried out on metal studs. The kit of such a device contains brass nuts, as well as crescent-shaped gaskets. The sanitary fixture is sealed using a rubber insert of the same shape. There are models with one pin, but it is better to choose products with two locks. This design provides a more reliable fixation of the device.

Assembly

Installing a faucet in the kitchen with your own hands begins with its assembly. This device provides simultaneous supply of hot and cold water and has the appropriate mechanisms. The crane package includes:

valve;
spindle;
device head with rod and flywheel.

At the initial stage of work, eccentrics are installed, which are supplied by the manufacturer along with the sealant. If there is no such material, then it is necessary to wrap the tow in a thin layer, which insures the device from possible water leakage. If there are thick walls in the mixer body, threads are also wound to secure the adapters.

Save

Installation on the sink

Soak the fiber pads in cool water for 10 minutes. Such operations are not carried out with silicone or rubber sealing elements. Next, we attach the faucet to the eccentrics using union nuts.

At the next stage of work, we install the gaskets in the right place and begin to clamp the tap, first manually, then using an adjustable wrench. During such work, distortions should not occur, so the nuts are screwed in several turns one at a time. When the installation of the kitchen faucet is completed, check its correct position and the strength of the fastening; the faucet should not wobble.

Save

With nut fastening

This option for installing a faucet in the kitchen begins with attaching the faucet itself to the sink. The device comes with a rubber seal in the form of a ring, which is inserted into a groove on the mixer body. After this, we screw the product into the thread on the sink and install a rubber gasket at the bottom. Next, screw the brass nut with the skirt down and press the sealing element. We tighten the nut with a wrench until we ensure that the mixer is in a stationary position on the sink.

At the next stage of work, we begin to secure the hoses. We screw them into the thread using a No. 10 key. There is no need to wind the tow onto the thread; just install a rubber sealing ring. Tighten the hoses carefully so as not to destroy the material. After this, the inlet pipes are connected to the pipes with hot and cold water.

Save

With stud fastening

In this case, flexible hoses are installed on the mixer before it is installed on the sink. In the absence of such operations, the plumber will not be able to tighten them efficiently.

Installation of a faucet in the kitchen takes place in the following order:

Remove the nuts from the studs and tighten the threaded parts at the end of the faucet. The screwing depth of the thread is within 8-10 millimeters.
We try on a shaped gasket and a steel plate on a stud.
We pass flexible hoses through the holes with the fittings facing up.
We control the presence and position of the rubber sealing ring on the tap.
We screw in the hose fittings, first the short one and then the long one.
We install the faucet in the sink or countertop, install a metal gasket and a sealing gasket at the bottom, attach and tighten the nuts.
Tighten the nuts on the studs well. The mixer should not wobble.
We control the tightness of the connection.

After installing the mixer, we fix the sink on the countertop in its original position.

Save

To secure the sanitary fixture to the countertop, you need to prepare the following tool:

set of drills;
electric jigsaw;
electric drill.

Now we will learn how to install a faucet in the kitchen on the countertop. First you need to determine the location of its attachment. After the sanitary fixture is securely fastened, liquid should not spill onto the countertop, and the user should be able to comfortably use the lever.

Next, take a pencil and make markings on the countertop where the sanitary fixture is attached. Now we make four holes with a drill, then turn on the jigsaw to cut the hole. We clean the cut area from sawdust and dust, and rub the edges. At the final stage of work, we place an o-ring and a washer, and screw the mixer to the countertop.

Save

Connection to communications

We have learned how to install a faucet in the kitchen, now we will look at how to connect it to utilities. First, we tighten the eccentrics that connect the mixer to the pipes. To prevent condensation from forming between the hot and cold water hoses, it is necessary to leave a distance of 15 centimeters.

Tow is wrapped around the thread and coated with sealant. Fum tape can be used for the same purpose. After this, screw the mixer nuts onto the eccentrics and secure the special cover. This element must be secured manually; it must fit well to the wall. If there is a gap of less than 5 millimeters, the tap is disconnected and the eccentrics are shortened to the required length.

Next, install paronite, rubber or silicone gaskets into the housing nut, which will ensure a tight fit of the mixer to the eccentrics. At the final stage of the work, the nuts of the inlet pipes for hot and cold water are tightened manually; if a leak is detected during the check, they are additionally tightened with a wrench.

Save

Functionality check

After the faucet is installed in the kitchen, it is necessary to check its functionality. To do this, open the valves for supplying hot and cold water and inspect the attachment points of the flexible hoses. If leaks occur, tighten the nuts. When carrying out testing, it is necessary to turn the tap on and off, turn the lever and check the efficiency of mixing water.

When installing a faucet in the kitchen, try not to twist the supply flexible hoses. Always ensure that gaskets are present in the required places on the plumbing fixture and on the threaded connections. The biggest mistake is to over-tighten the nut at the junction of the hose and the supply pipeline. Rubber gaskets are installed in these places, they are tightened by hand, and only when a leak appears can the nuts be gently pressed with a wrench.

A major bathroom renovation necessarily includes the installation of a new faucet. By figuring out how to install a faucet yourself, you can save a significant amount on plumbing services. The procedure will vary depending on whether you need to install the equipment from scratch or replace an old device.

Dismantling Guide

If your bathroom already has plumbing installed, you will need to get rid of the old device before you just purchase it from the store. To do this, turn off the water supply by turning the appropriate valves, and then open the taps to relieve pressure in the pipeline.

Sometimes it happens (especially often in old houses) that the inlet valves rust and do not completely shut off the water supply (it flows in a thin stream or drips). In this case, you will need to do the following: if you cannot completely shut off the cold water, open a cold water supply tap (usually the tap that supplies water to the toilet) located below the faucet outlets. As a result, the water will flow through the bottom tap, and you can calmly begin dismantling and installing the faucet in the bathroom.

If it is not possible to discharge water using this scheme, you will have to go to the housing office or another management company and write a statement asking to completely turn off the water risers while the work is being carried out. Be prepared to pay extra for this service.

Check again that there is no water. If it does not flow, take a wrench and, one by one, unscrew the nuts that secure the mixer to the water supply system. When unscrewing, the key should be turned counterclockwise.

Remove the old faucet and look into the supply pipes. Quite often, an additional filter is installed before entering the tap. After a certain period of operation, this filter becomes contaminated with rust, scale and other elements, which significantly reduces throughput. Carefully remove all foreign matter.

After this, you can begin installing new plumbing. However, before installing the faucet, you need to familiarize yourself with a number of rules and requirements. They will help you complete all the necessary work faster, and the installed product will serve for a long time without failures or complaints.

Return to contents

Theoretical knowledge

In most cases, bathrooms already have female end fittings for . If you do the wiring of highways with your own hands, consider the following important points:

The axes of the hot and cold water supply inlet fittings should be installed at a distance of 15 cm from each other.
Hot water is supplied from the left, and cold water is supplied from the right.
It is most convenient to use a mixer installed at a height of 15-20 cm from the bathtub and 60-80 from the floor level. Therefore, it is best in this position.
Recess the inlet fittings into the wall. This must be done in such a way that when laying the tiles on the wall, the ends of the fittings are located flush with the front side of the ceramic tiles. Thanks to this, you can hide the connection points of the plumbing fixture behind decorative cups.

It is best to use plastic pipes for plumbing. They are cheaper and more practical than steel and cast iron products, and even a person without experience can cope with welding such pipes.

Return to contents

Step-by-step instruction

Prepare tools for installation:

gas and adjustable wrenches;
FUM tape (can be replaced with ordinary tow or linen thread);
set of hex keys;
pliers;
Screwdriver Set;
open-end wrenches.

Often, when installing inlet fittings, it is almost impossible to maintain a distance between them of 150 mm. If you made a small mistake, then it’s okay. Especially for this purpose, adapter eccentrics are included with the plumbing fixture.

Take your chosen sealing material and wrap it around the threads of the eccentrics, then screw them into the water main inlet fittings. Rotate the eccentrics to obtain a distance equal to or as close as possible to 150 mm. Check the horizontal installation using a building level.

Pre-screw the body of the new mixer and make sure it is horizontal. Check how the union fastening nuts are tightened. They should be fairly easy to tighten by hand over the entire thread of the nut. If it is quite tight, you will need to make fine adjustments by slightly turning the eccentrics, thereby achieving unhindered tightening. After this, you will need to screw on decorative cups that will hide the place where your new faucet connects to the main line.

Insert the sealing gaskets and install the product body in place. Take the wrench and tighten the mounting nuts. Be sure to place a piece of soft cloth under the jaws of the wrench so as not to spoil the coating of the nuts and the overall appearance of the product.

There is no need to tighten the nuts too much. The connection will seal perfectly through the gasket, and there will be no leakage.

Just in case, you can apply pressure to the line and make sure there are no leaks. If it is present, you need to additionally tighten the nuts until the leak is completely eliminated.

Next you will need to install the gooseneck. Install the nut and tighten it with a wrench through a piece of fabric. Insert the gasket and screw the watering can hose to the main body. Insert another gasket, only this time to connect the watering can with the hose. Mark the position and attachment points of the watering can holder.

Next, you will need to drill holes for the fasteners and attach the watering can holder bracket to the wall. After this, the process of installing a faucet in the bathroom yourself can be considered complete. Finally, you will need to open the shut-off valves, make sure the mixer is working properly and check the tightness of the connections.

Each of us has faced such a problem as replacing a faucet. This can happen due to wear and tear of the old one, or if you are renovating and decide to install a new faucet.

You always have the option of inviting a specialist to install it for you, but you will have to pay for this service, or you can install it yourself and spend the saved money on other needs. Installing a faucet is not that difficult.

In this article we will tell you in detail how to properly install a faucet in the bathroom and provide video instructions on this topic.

Nowadays there are two main models of mixers - lever and valve. Each option has its own advantages and disadvantages:

Lever- very easy to use, but adjusting the water temperature is very difficult, especially when your hot water comes from a boiler or gas water heater. Shower switch problems are also very common.
Valve– this model is familiar to everyone. The advantage of these faucets is more precise adjustment of the water temperature, as well as a more durable shower switch. The disadvantage is the valves themselves, or rather, the fact that because of them it very often drips from the gander and requires frequent replacement of the gaskets.

There are other models, more about which you can find out on this one. If you want to know how to choose and install a bathroom faucet with shower,... Also when choosing a bathroom faucet pay attention to the following nuances:

The faucet coating (chrome) must be perfect. Any defects in the coating will further accelerate the destruction of the coating and spoil the appearance of the mixer.
Should be heavy then it's made of brass. Only faucets made from brass are durable.
Check the package.

The complete set of the mixer includes the following parts:

Mixer body;
Gander;
Going to the shower;
Decorative lampshades;
Shower head;
Shower hose;
Gaskets;
Wall mounting (if the faucet is a lever faucet).

Even the most reliable faucet can leak if installed incorrectly or used for a long time. Find out if and if this is possible.

Did you know that there is a faucet with a water supply sensor? More about it, its advantages and disadvantages.

Preparing for work

You will need the following set of tools:

Adjustable wrench;
Gas key;
Fum tape - fluoroplastic seal;
Drill;
Hexagon No. 10;
Roulette.

It is better to use the second number for an adjustable wrench, it will be much more convenient for you during installation. A drill if you need to install a shower wall mount. You can also wrap tow with a special paste, but for a beginner it will be easier to work with fum tape.

When installing a mixer, in fact, you only need to wind up one side of the eccentric, which is screwed into a corner in the wall, and everything else is assembled strictly on gaskets, and winding in these connections will not help at all.

Installation instructions

We turn off the water.
We fasten the eccentrics.
We put on decorative lampshades.
Screw on the mixer body.
We install the gander.
We install the transition under the shower hose.
We screw on the shower hose and watering can.
If required, we attach a shower mount to the wall.

And now Let's look at each step Installing a faucet in the bathroom with your own hands in detail.

Most people have the most problems with the first point. It's good if you had a mixer before, which is out of order and you simply change it. Then you are all ready, you just need to screw on the mixer body and that’s it.

If installation of eccentrics is required, then we wrap the half-inch thread with fum tape, wind the seal strictly clockwise and make from 4-10 turns it all depends on the thickness of the fum you purchased.

After this, we screw a one-inch corner into the floor, which is hidden in the wall. By tightening it with a gas or adjustable wrench, the eccentrics are installed so that the distance between centers was strictly 15 cm so that the mixer can be easily screwed on.

If the nuts are easily screwed during installation, then you did everything well. If the nuts are tightened tightly, this will lead to big problems in the future. At some point the nut or brass sleeve that holds the nut will break, so it's better to fix the eccentrics.

Now we can open the water and check if we have any leaks. If everything is normal, then we continue with the installation. If not, then you need to fix the problem.

After installing the lampshades, screw the mixer body. To do this, insert gaskets into the nut on the mixer body, and screw the nuts to the eccentrics.

First, tighten the nuts as much as possible by hand, only then tighten the nuts with an adjustable wrench, literally making 1-2 turns. You should not tighten too much, otherwise you can cut off the gaskets and then you will need to install new ones.

Now we screw the gander to the body. It is only screwed on by hand and no keys are used. To do this, press the gib firmly into the hole intended for it, and then the nut will be easily screwed on.

If there is a leak from under the gander, there is no point in tightening it with an adjustable wrench or a gas wrench, it is necessary to replacing the gander with a new one.

Next, we install the transition under the shower hose, which also serves as a mount for it. It is screwed with a three-quarter nut to the hole on top of the mixer. Having previously inserted a gasket into the nut, twist and tighten tightly by hand.

What to do, if ? Find out everything about the causes of the problem and ways to solve it.

What is attractive about Aquatherm, Delimano and others water heater taps and why are they chosen instead of traditional mixers? Find out.

Lever faucets, some older models, may have a special tee (moon) adapter for connecting shower hoses. It is mounted between the gander and the mixer body.

We screw the shower hose to the transition to the shower. To do this, insert half-inch spacers into the nut on the hose and tighten by hand. If required, you can tighten it a little with a wrench.

We screw the watering can to the hose, not forgetting to install the gasket in the nut on the hose. We twist strictly by hand.

The nuts on the shower hose come in different shapes - elongated, conical, and the other standard. The cone nut is screwed to the watering can, and the regular nut is screwed to the mixer.

And the last thing - installing a wall mount. Only lever valves are equipped with fastenings. In valve mixers, the watering can is located on the mixer.

Take a look at the DIY process of installing a bathroom faucet in this video:

Important Details

When tightening the nuts with a wrench, be sure to place a piece of rag between them, this way you will not scratch the mixer. If the mixer is damaged, the warranty on it automatically expires..

Before installation, use a No. 10 hex to tighten the brass bushings on the mixer that press ¾ nuts on body.

Installing a faucet in the bathroom yourself is not a very difficult task; the main thing is to carefully and carefully follow each step when installing the faucet. As a result, you will be pleased with the new faucet on the wall that you were able to install yourself.

To work you will definitely need:

new mixer with a set of parts for installation;
open-end wrench 10;
tubular wrench of the same size;
plumbing sealing tape or tow;
pliers;
flat screwdriver;
rags and a basin for collecting water;
flashlight.

When purchasing a mixer, it is important to pay attention to the connecting hoses that come with it. Manufacturers often save on this useful detail by offering eyeliners no longer than 30 cm. In most cases, this is not enough, so before installation it would be a good idea to buy new ones of longer length.

Some models are equipped with rigid tubes. This is a controversial decision. On the one hand, such an assembly is stable and reliable, but difficulties may arise if it is necessary to move the sink. If possible, they should be replaced with hoses.

Regarding the length of the connectors. It is selected based on the distance between the installation location of the mixer and the water supply outlet so that they do not bend at a right angle, but create a smooth curve, but do not sag too much.

Preparatory work and dismantling

Before you begin repairing any plumbing fixtures, the faucet is no exception, you must turn off the cold and hot water supply. There is no need to shut off the riser in the entrance; it is enough to use the taps that regulate the water supply to the apartment. If there are valves that regulate the water supply only to the kitchen, you can limit yourself to them. Immediately after this, you need to open both mixer taps to balance the pressure.

After this, you can unscrew the supply hoses. The water accumulated in them is poured into a basin and allowed to drain completely. The time for the most difficult part comes - you need to unscrew the nuts holding the old device in place and dismantle it. At first glance this is simple, but in practice everything is far from so. Dismantling the mixer involves a number of difficulties:

narrow space between the wall and the bowl;
extremely uncomfortable position for working with a key;
rust and plaque on the threads.

It is extremely inconvenient to work in tight spaces; you can’t get to the nuts with a wrench; if the threads are oxidized, it’s easy to “lick” the edges. This is a problem, but the mixer must be removed, therefore, you will have to look for a way out. In some cases, this will involve dismantling the sink. It can be easily removed, you just need to disconnect the sewer drain hose and walk around the perimeter with a sharp object, knife or screwdriver.

It is enough to remove and turn the sink over, and most of the inconvenience will go away by itself. You can slowly inspect the connection in the light and choose the optimal dismantling strategy.

Advice! It is easy to overcome rust and oxide layers using WD-40 or its analogues.

If everything is very bad, if the connection has “grown together,” you will have to take up the grinder. It is important to work with extreme caution to avoid damaging the thin metal.

Sequence of actions during installation

Before changing the faucet in the kitchen yourself, it would be useful to check the condition of the supply pipes, especially the threaded parts to which the hoses will be screwed. The cut of the pipe at the joint must be even and smooth, there should be no chips or cracks that would damage the seal. The same applies to carving.

Certain types of mixers must be assembled before installation. This applies to a greater extent to models with two valves. Single-lever products are ready for installation; there is no need to assemble them. Assembly is not particularly difficult; you just need to insert the drain tube into the housing and screw it until it stops. To ensure maximum tightness, the lower part of the thread is wrapped with several layers of FUM plumbing tape.

Next, the device is turned over and the supply hoses are screwed on. Twist it by hand, tighten it with a wrench, but it is important not to overdo it so as not to crush the gasket. After this, the installation studs are screwed on, and the o-ring is put on the body from below. The mixer is ready for installation.

Installation of a faucet on a sink

The work is much easier if the sink was removed during dismantling. In this case, you won’t have to squeeze into the narrow space underneath and literally navigate by touch.

Often, replacing a faucet is combined with installing a new sink. Stainless steel sinks are available with or without a hole for the faucet. Manufacturers try not to limit users and give them the opportunity to choose the optimal location of the taps themselves. If you purchased a sink without a hole, you will have to do it yourself.

Making a round hole in stainless steel is easy. For these purposes, a special tool is put on sale, which operates on the principle of a screw press. It is enough to drill a central hole, insert a screw into it, clamp the device with a key, and you will get a hole of exactly the specified diameter. You can also use a drill attachment.

Work begins from the top of the sink. The ends of the hoses are inserted into the hole, followed by the pins. Press the body against the surface of the sink. It is advisable to ask someone to hold the mixer while you put the second o-ring on the bottom. The result is two rings, between which the sink is sandwiched.

A horseshoe washer is installed on the mounting studs, it is secured with nuts and securely holds the device. After this, all that remains is to put the sink back in place, if it was removed, and, of course, connect the hoses to the pipelines.

Tabletop installation

Often the faucet has to be placed not on the sink, but on the countertop of the kitchen unit. This simple technique allows you to create not just a functional kitchen, but also give it originality, because the mixer, by and large, can be installed almost anywhere on the table.

This installation method is not much different from the previous one, the only significant difference is that before installation you need to cut a hole for the device body. In most cases this is not difficult. The worktop, like most kitchen furniture, is made of wood or wood-based panels, so you can use an electric jigsaw or electric drill with attachments for drilling large holes.

Before making a hole, you need to choose the optimal location for it. The main requirements for it:

water does not flood the countertop;
easy access to controls;
The center of the spout is located approximately in the center of the sink.

Using a pencil, ruler and compass, mark the installation location of the mixer. It is important not to miscalculate the size, otherwise you will not be able to fix the device. The walls of the hole are cleaned with sandpaper, shavings and sawdust are removed. Thread the hoses inside and fix the mixer.

Features of wall mounting

It’s not difficult to create an original kitchen with your own hands; just a small touch is enough and its appearance will change dramatically. A similar touch, an addition to the interior, can be a simple-looking faucet, but installed on the wall. It looks really impressive, the pipes are hidden, only the drain and controls come out. This is an interesting design solution that will become the highlight of a modern designer kitchen.

Note! Ordinary faucets are not suitable for wall mounting; you need to buy special ones.

The range of wall-mounted kitchen faucets is very wide. There are models with two valves, with a lever, with a rigid or movable spout.

The method of attaching the mixer to the wall directly depends on its type and model. Famous manufacturers take care of customers and complete the product with everything necessary. As a rule, connectors, eccentrics, tees and brackets are included in the delivery package. The buyer is only required to follow the instructions, which describe the installation process step by step.

A wall-mounted faucet is beautiful and functional, but you need to understand that its installation is more labor-intensive than installing conventional devices. Most likely, you will have to hollow out the wall, lay pipes, fix them, and re-tile them. It’s easier to work with drywall or panels, but in any case, installing such a mixer will result in a small kitchen renovation.

If difficulties do not frighten you and you want to install a wall-mounted mixer, you need to start with markings. Mark the hot and cold water connection points directly on the wall and mark the route for laying the pipelines.

Connection to water pipes

Before connecting the faucet in the kitchen to the water supply, it is worth checking once again that the installation is correct; it is unlikely that anyone will be happy with a fountain gushing from under the sink, caused by one nut that is not fully tightened.

There should be no difficulties connecting conventional models; using a wrench, screw in the connecting hoses, controlling the pressure force. The nut must be securely tightened, but without fanaticism, otherwise the gasket can break and water will ooze out at the joint. When laying the hose, you must ensure that there is no excessive bending, the transitions should be smooth, and the hose should not be stretched.

Most wall-mounted faucets have eccentrics. These are adapters, on one side of which there is a thread for connecting fittings, on the other - for holes in the case. In addition to the difference in thread diameter, their centers are somewhat spaced apart. After screwing in, the distance between the outlets will be 150 mm, which ensures a reliable connection and does not allow condensation to form.

Note! Connecting a wall-mounted mixer starts with the eccentrics. They are screwed into the body, having previously wound tow or plumbing tape onto the threads.

It is easier to work with the tape; moreover, it is more durable and does not swell during use. It would be a good idea to drip a little sealant onto the edge of the thread; this will guarantee no leaks throughout the entire service life.

Decorative overlays are put on the eccentrics; they will hide possible imperfections in the wall at the place where the pipes exit and give the plumbing completeness. All that remains is to put the gaskets and tighten the nuts. First this is done by hand, the last turn is done with an adjustable wrench. Work is done.

You can use the new mixer immediately after its installation, but first you need to make sure the connections are secure. To do this, just run the water, first hot, then cold. Using a flashlight, carefully inspect the hoses, paying special attention to the joints. If water does not ooze out, then everything is done correctly, the mixer is installed, it is guaranteed to last for more than one year.

When adding water to the kitchen for the first time, consider yourself very lucky. In this case, you can immediately do everything ergonomically and correctly - arrange comfortable access to the system and a “dry” way to replace equipment. When connecting to a ready-made network, there are also chances to not only install a faucet in the kitchen, but also install pipelines according to the above template. Today we will deal with both the first and second options.

You will be able to perform all the manipulations yourself, without the help of specialist plumbers. It will be two in one - you will acquire new skills and save your family budget.

Take into account

Security questions:

Risk areas arise when water is supplied to the system at various connections, where rubber or rubberized products act as gaskets.

Advice: plan the installation of pipelines in such a way as to minimize the number of connections in the area between them.

Installation of shut-off valves. Usually they are recommended to be installed on the main pipeline, and then to it.

Advice: a good rule of thumb is that each water distribution point must be equipped with a shut-off ball valve.
Then you have the opportunity, if necessary, to block the desired area without affecting the entire system.

Plumbing equipment. How many times have they said that a low price is not your luck when buying, but usually quite the opposite. Inexpensive equipment and connecting hoses often have poor manufacturing quality, so they rarely last the warranty period.

Tip: one way to choose the right mixer is to focus on the brand and customer reviews.
In both cases, operational reliability approaches 100%.

Preparation

We invite you to familiarize yourself with useful little things that will help you in your future work. Ultimately, the final result will depend on them:

Mixer	The main criteria should be added that the spout should be directed to the center of the sink. Pay attention to the complete set of the product, which includes flexible hoses and gaskets (rubber, silicone or paronite). Check the warranty mark in the instruction manual.
Nuts	When purchasing, pay attention to the diameter of the connecting nuts and couplings. The standard option is 1/2″, but if it is larger or you decide to connect the equipment directly to the main pipe, use an adapter.
Mixer socket	When the sink already has a hole for the tap, check that its diameter matches it. In its absence: in a ceramic or stainless sink - you can drill a seat using special tools yourself or directly in the store (if such a service is available); purchase a wall-mounted version of the faucet.
Tool	You will need a minimum set - a screwdriver, pliers, 2 adjustable wrenches. We recommend stocking up on WD-40 lubricant, which will greatly facilitate the dismantling of old equipment.

Start of the process

The instructions below will answer all questions related to installing a faucet on a kitchen sink. We recommend that you first cover the area of intended work with packaging cardboard or other material so that metal parts falling from a height do not damage the floor covering or cabinet. If possible, move the sink away from the wall.

Tip: if access to the mixer is possible only from one side, remove everything that will interfere with work.
This is usually a wastewater disposal system.

In the photo - shut-off valves will allow installation without shutting down the entire water supply system

Installation

The step-by-step work will look like this:

Place the entire structure in the prepared nest. You can clearly see this in the package insert provided by the manufacturer.
So:

Install a rubber gasket on the hole;
place a metal base plate on top;
insert the mixer itself;
Place another gasket on the metal threaded stud from below;
tighten everything with the fastening nut.

Tip: there are fasteners that do not have an internal rubber ring. Fixation is done manually without any tools. This should be written in the equipment assembly manual.

Connect cold and hot water connections to your sockets. The clue will be the logo on the faucet lever, which has a “red” and “blue” half, respectively.

Tip: you can install the hoses before installing the mixer in the sink hole, this is not important.

Take an adjustable wrench and connect each hose to its own line.

System startup and repair

Connection, as you can see, is not complicated, the main thing is to be careful in your work. All that remains is to make the first launch of the system, which will answer many questions.

To do this, open the shut-off taps, and then alternately, and then together, the cold and hot water taps. Inspect the connections and, if there is slight leakage, tighten the nuts. However, do not overdo it so as not to break them.

Now let's look at several issues related to equipment repair:

Periodically check the connecting hoses at their connections. If they begin to leak water, replace the gaskets. When water starts leaking from the hose itself, replace it with a new one.
In two-valve faucets, a common cause of water leakage is worn out cartridges. They should also be replaced; the process is not difficult.
|To do this:

unscrew the colored nozzle on the valve;
unscrew the valve locking bolt with a screwdriver or hexagon and remove it;
disconnect the connecting nut securing the cartridge;
replace the failed cartridge with a new one.

If water begins to leak from the mixer body, the equipment itself requires replacement.

Conclusion

Today we told you how to install your favorite faucet in the kitchen with minimal difficulties. Now you should have no blind spots associated with this process.

The main thing is to be careful and consistent. The video in this article will give you the opportunity to find additional information on the above topic.